routers

comprawifi.com/routers-aps-switch/routers-y-aps
Fuente
Zonet ZSR1134WE como repetidor

Zonet ZSR1134WE conectado por el cable de red
1.-ingresa a el router mediante la dirección IP 192.168.1.1
la contraseña y el usuario por defecto es guest pero se puede cambiar dirigiéndose a la opciòn system management.
2.-una vez dentro del menú de configuraciones ve a la opción wireles /basic settings, en donde dice AP lo cambias por client y en donde dice Enable Universal Repeater Mode activas la palomita de la izquierda. en el recuadro SSID of Extended Interface escribe el nombre que quieras para la interfaz del repetidor. (no olvides oprimir save setings y después OK en todo lo que hagas.)
3.-te vas a la opcion security, en Encryption le pones el tipo de clave que usa el AP si es wep o wpa2.
una vez listo oprime el boton [set wep key] y escribe tu clave si es wep.
si es WPA o WPA2 escribela en el recuadro que dice preshared key en la opcion Wireless Security Setup.
4.-ve a wireles /site survery oprime [refresh], elije tu AP marca select oprime connect y ok
5.- ve a LAN SETUP y cambia la ip por defecto y agrega tu puerta de enlace predeterminada
Y des habilita la opción de DCHCP
ejemplo DE ip 192.168.1.126 y en gateway 192.1168.1.254 (Telmex México ) tu deberás poner la puerta de enlace predeterminada de tu compañía de Internet si no sabes cual es ejecuta cmd y escribe en la ventana de cmd ipconfig
Nota si no tienes Internet después de configurarlo ejecuta nuevamente cmd y escribe:
ipconfig /release seguido de eso ipconfig /renew. (para renovar la dirección ip del la computadora.
Manual of Zonet router
Troubleshooting  of Zonet ZSR1134WE
Q1. I cannot access the Web-based Configuration Utility from theEthernet computer used to configure ZSR1134WE.
Check whether the LAN LED is on. If the LED is not on, verify the cable for theLAN connection is firmly connected. 
Check whether the computer resides on the same subnet with ZSR1134WE’sLAN IP address.
If the computer acts as a DHCP client, check whether the computer has beenassigned an IP address from the DHCP server. If not, you will need to renewthe IP address.
Use the ping command to ping ZSR1134WE’s LAN IP address to verify theconnection. Make sure your browser is not configured to use a proxy server. Check that the IP address you entered is correct. If ZSR1134WE’s LAN IPaddress has been changed, you should enter the reassigned IP addressinstead.
Q2. I forget Password (Reset ZSR1134WE without Login) 
Plug out the power of ZSR1134WE.
Use a pencil to press and hold the default button on the back panel of ZSR1134WE. Then plug in the power of ZSR1134WE.
Press and hold the default button for few seconds until the CPU LEDindicator stays green.
Reboot ZSR1134WE.
After above steps, the factory’s default settings will be restored inZSR1134WE. The default user name/password is guest
Q3. I have some problems related to Connection with Cable Modem
Please follow the steps to check the problems:
Check whether the DSL modem works well or the signal is stable. Normallythere will be some indicator lights on the modem, users can check whetherthe signal is ok or the modem works well from those lights. If not, pleasecontact the ISP.
Check the front panel of ZSR1134WE, there’s also some indicator lights there.When the physical connection is correct, the Power light and the CPU lightshould be steady; the WAN light should be flashing. If you use your computer,the corresponding LAN port light should be flashing too. If not, please checkwhether the cables work or not.
Repeat the steps in WAN Setup
Connect with Internet through DSL Modem.
Q4. I can browse ZSR1134WE’s Web-based Configuration Utility butcannot access the Internet. Check if the WAN LED is ON. If not, verify that the physical connectionbetween ZSR1134WE and the DSL/Cable modem is firmly connected. Alsoensure the DSL/Cable modem is working properly.
If WAN LED is ON, open the System Overview page of the Web configurationutility and check the status group to see if ZSR1134WE’ s WAN port hassuccessfully obtained an IP address.
Make sure you are using the correction method (Dynamic IP Address, PPPoE,or Static IP) as required by the ISP. Also ensure you have entered the correctsettings provided by the ISP.
For cable users, if your ISP requires a registered Ethernet card MAC address,make sure you have cloned the wireless client’ s MAC address to the WAN portof ZSR1134WE. (Refer to
MAC Address field in WAN Setup .)
Q5. My wireless client cannot communicate with another Ethernetcomputer.
Ensure the wireless client functions properly. You may open the DeviceManager in Windows to see if the adapter is properly installed.
Make sure the wireless client uses the same SSID and security settings (if enabled) as ZSR1134WE.
Ensure that the wireless client’s TCP/IP settings are correct as required byyour network administrator.
If you are using 802.11b wireless adapter, but selecting the 802.11G Mode in Wireless Basic Setting page; it is not configured to use 802.11g Performance.
Use the ping command to verify that the wireless client is able tocommunicate with ZSR1134WE’s LAN port and with the remote computer. If the wireless client can successfully ping ZSR1134WE’ s LAN port but fails toping the remote computer, then verify the TCP/IP settings of the remote computer.